VAMO V2 VV/VW (MOD) - KROM

295,00DKK

Dette batteri-mod får gode anmeldelser - bl.a. andet for at være et af de bedre prisbillige VV/VW Mod på markedet. Udover den finde ydelse og funktioner, er mod'et i nydeligt design (Krom)

OBS! Produktet er udgået til fordel for Vamo7

Model/varenr.: SP-MOD-VAMO
Vægt: 0.200
Lager: Ikke på lager
  Få besked når varen kommer igen
GRATIS levering!

VAMO VV/VW MOD m. 510/EGO threading (KUN SELVE MOD U/TILBEHØR)

Dette batteri-mod får gode anmeldelser - bl.a. andet for at være et af de bedre prisbillige VV/VW Mod på markedet. Udover den finde ydelse og funktioner, er mod'et i nydeligt design (Krom)

Mod virker med alle atomizers med 510 og ego gevind og i benyttes variable watt indstillingen justerer mod'et selv output så det passer til de fleste atomizer modstande over 1.2ohm. Vamo har en cut-off ohm funktioner, der slår fra ved lavere ohms (på atomizere under 1.0 ohm).

VAMO er et godt og prisbilligt mod med en imponerende liste af funktioner:

VAMO VV/VW MOD (KIT) - Instruktionsvideo af Mike Johnsen



OBS!
DENNE VIDEO MANUAL ER LAVET MED FØRST VERSION AF VAMO V2 VI FIK PÅ LAGER, DEN VISER VAMO V2 MED TILBEHØR (FRA VAMO KITTET), DENNE VARER INDEHOLDER KUN SELVE VAMO MOD'ET.

VAMO V2 - PÅ LAGER ER NY MODEL AF V2 MED FLG. FORBEDRINGER:

  • Hotspring (Batteri fjeder) - Forbedret leveevne/materiale
  • Pænere finish - Bedre overall look
  • Top gevind og pakningsring
  • Metal knapper i stedet for gummi (pga. efterspørgsel stort hos kunder på)


Specifikation på Vamo VV/VW MOD

- Variable Volt: 3~6.0V,
- Variable Watt: 3~15W.
- Gevind: 510/EGO
- PWM (Pulse Width Modulation) output, op til 5A
- 5 Klik tænd/sluk
- Kan bruges med flere batterkonfigurationer: f.eks 1x 18650, 1x 18350 or 2x 18350
- Pol-beskyttelse og kortslutningsbeskyttelse
- Advarsel ved for lav ogm eller lav batteri

Denne varer er kun selv Vamo VV/VW Mod Body V2 uden batteri, atomizer, adapter eller lader.

Fuld samlet kan VAMO bruges sammen med 1 stk. 18650 eller 2 stk.18350 ved at fjerne nederst del af kroppen på mod'et kan man monterer 1 enketlt 18350.
VAMO MOD kræver ikke beskyttede batterier.

9/5-2013
NYE MODS LEVERES INKL. NY VAMO "HOTSPRING" (BATTERIFJEDER)- DER FORBEDRER MODDETS BATTERIKONTAKT OG DEN GENERELLE YDELSE BETYDELIGT.

How to use chrome Vamo VV/VW Mod Body V2:

Turn On or Off:
Press the Power (large) button 5 times within 2 seconds.

Switch between VV and VW:
Press and hold + and - buttons for 3 seconds (v for volts, w for Watts).

Voltage adjust:
Tap the + or - buttons to raise or lower output voltage (in .1 volt increments).

Wattage adjust:
Tap the + or - buttons to raise or lower output wattage (in .5 watt increments).

Resistance check:
With an atomiser or cartomiser installed on unit, press and hold the + button for 2 seconds. Atomiser resistance is displayed in ohms.

Battery voltage check:
Press and hold the - button for 2 secs to check actual battery voltage

IMPORTANT
The Vamo can display output voltage and wattage as an Average or as RMS (Root Mean Square). RMS is the actual and true output and is the one to use.

Press and hold the + button for 10 secs. If no2 is shown then the output is already set to RMS, no further action is required. If no1 is shown, release the button and press again for 10 secs until the display shows no2. This setting should not alter after a battery change, however if the vape feels warmer than expected please re-check setting.

Error codes:
LO-Ω : Atomiser resistance is too low (below 1.3 ohm).
LO-v : Atomiser shorted

Display will flash when battery needs replacing/recharging (approx 3.4v).

Voltage or wattage level resets when battery is removed, the mode does not.

Usage of eGo style cartomisers/clearomisers:
The Vamo has a recessed atomiser fitting with a large opening to accommodate the eGo skirt. Most popular atomisers and cartomisers will fit, however if you use a wide skirted unit (eg: Kanger T2 or T3 clearomizer) you will need to fit a 510-EGO adaptor.
 

Vamo Detachable VV & VW Mod V2.0 with RMS feature

The Vamo has a recessed atomiser fitting with a large opening to accommodate the eGo skirt. Most popular atomisers and cartomisers will fit, however if you use a wide skirted unit (eg: Kanger T2 or T3 clearomizer) you will need to fit a 510-EGO adaptor..

With the new detachable design, the Vamo Mod can work with 1pc 18650 battery or 2pcs 18350 batteries; also it can work with only 1pc 18350 battery.

Voltage is delivered via PWM (Pulse Width Modulation) with a maximum current of 5A.
In ‘long’ mode on the left the device can be used with one 18650 battery or TWO 18350 batteries. On the right in ‘short’ mode the device is using a single 18350 battery.

Protected type Li-Ion batteries will not work in this device – the over current protection renders them unusable as they usually have a current limit of 2.5 Amperes and this device uses current higher than that figure.. Please use High drain Safe rated batteries with no on-board protection for optimum use of this device.

Recommended batteries are IMR / AW type cells.

There are 3 buttons on the Vamo's body, please take a look at the image below: Metal buttoned versions are not marked with symbols

NOTE that the negative button is the LEFT button and the positive button is the RIGHT button.

Note: when a battery is inserted the screen may flash once and then turn off – the device is not yet turned on – you will need to click the power button 5 times to turn the device on. Your device is not faulty! Remember you must turn the device on!

Adjustment Button: Press the button to increase the voltage from 3.0v-6.0v in 0.1V steps, when you reach 6.0 v, it will start back from 3.0v. In wattage mode 3.0 to 15 Watts in 0.5 Watt increments when you reach 15 Watts it will start back from 3.0 Watts

Adjustment Button: Press the button to decrease the voltage from 6.0v-3.0v in 0.1V steps, when reach 6.0 v, it will start back from 6.0v. In wattage mode 15.0 to 3.0 Watts in 0.5 Watt increments when you reach 3.0 Watts it will start back from 15.0 Watts

Be aware of this feature as you might inadvertently set the voltage or wattage too high by accident.

Power Button: Press the power button 5 times, you can turn the device ON or OFF. Obviously the power button is used to activate the atomiser in actual operation. There is a safety cut out if the button is held down for more than 10 seconds duration.

VOLTAGE TYPE:

Voltage to the atomising device can be provided in two ways from the mod.

RMS and AVG. It is recommended that users use the RMS (Root Mean Square) mode as this will be a more reliable and accurate method of delivering consistently accurate voltage.

• Hold either the OR button for 10 seconds to toggle between modes.
• RMS mode = N02 displayed on screen
• AVG mode = N01 displayed on screen

Whatever version of the mod you may have the voltage method should be remembered even when batteries are changed.

VARIABLE MODES -- VOLTS OR WATTS

Your device can operate in Variable Voltage mode or Variable Wattage mode.

• Constant voltage. In this mode, you can adjust from 3.0 to 6.0 Volts in 0.1 volt increments. The voltage that you set will be maintained as accurately as possible by automatic adjustment of current delivery.
• Constant power. In this mode, you can adjust from 3.0 to 15 Watts in 0.5 Watt increments. The wattage that you set will be maintained as accurately as possible via analysis of voltage and current delivery.

Change modes by holding AND buttons at the same time for 3 seconds.

Resistance meter:

Hold the button down for 3 seconds and the resistance of the attached atomiser will be displayed.

Battery power check

Hold the button for 3 seconds to display current battery voltage.


Additional Safety features and Functions:

• When you press the power button to use the device for 10-15 seconds or more, the device will turn off automatically.
• When a single batteries voltage is less than 3.2v or dual 18350 batteries voltage is less than 6.4v, the screen will display LO v, which indicates that the batteries need to be recharged.
• Atomizers at 1.2ohm or less, the screen will display LO Ω, which indicates that you need to use a new atomizer at higher resistance.
• Atomizer short circuit the screen will display LO v.
• Incorrect battery installation protection. The device will not work circuits will be protected.
• Max current 5A
• Minimum resistance 1.2 Ω
• Thermal Monitoring
• Correct Polarity Signalling
• Heavy Duty Micro-switches
• Vent Hole in Battery End Cap
• Battery End Cap ‘fail safe’ designed to ‘give way’

Addendum:

Some versions of this mod were provided with a small spring in the base that proved to be temperamental with some flat headed 18650 batteries.

The original type of spring looks like this:

Later versions will be provided with an uprated spring – in the meantime you can retrofit any suitable spring from a cheap torch to rectify any problems you may encounter regarding flat headed 18650 batteries like so;

Vamo Detachable VV & VW Mod V2.0 with RMS feature