IMOTION V2+ MOD Starter Kit
Dette "kingsize" battery mods tilbyde mange muligheder for justering og har indbygget testet til atomizer ohm test. Imotion leveres inkl. batteri og 240V oplader. Læs mere...
*** ITEM IS NOT FOR SALE ***
+45 3876 1145
IMotion2 V+ Variable Voltage Electronic Cigarette Mod (No Atomizer devices included).
The IMotion2 V+ is a microprocessor controlled electronic cigarette that lets you adjust the voltage from 3.0V-6.0V in seconds with just a few button presses.
One starter kits includes:
1 x Batterry 1500mAh
1 x Complete tube
1 x 240V Battery Charger
1 x Manual UK.
Kit does not contain any atomizing parts!
IMotion2 V+ Features:
Uncrew the end cap for battery replacement.
Newest PCBA technology application
Full battery charged: approx. 4200puffs
The IMotion2 V+ can be adjusted from 3.0V-6.0V volts in 0.1 volt increments
The LED HD display voltage and display adjusted your voltage
Use Pulse Width Modulation for the voltage output
PCB allows 5 Amperage output limited.
Max Output power 20W
On/off Mode allows you to shut the unit off completely
Reverse battery protection keeps circuit safe if the battery is installed backward.
Battery Monitoring shuts the unit off once battery has reached end of charge.
Thermal Monitoring shuts the device off if it detects a high temperature condition?
IMotion2 V+ Settings
Setting Codes: VU,VD,SO,CB,DR,LO.
1. VU - Voltage UP (press 4 times)
2. VD- Voltage Down (press 5 times)
3. SO- Standby on/of (press 6 times)
4. CB -Check battery (press 7 times)
5. DR- Display Resistance (press 8 times)
6. LO-Led light on/off (press 9 times)
LED display shows the working voltage when vaping
You can adjust the voltage from 3.0-6.0. Note: The higher the voltage, the hotter the heating element will get! Always begin with a low voltage setting and increase the power until you are satisfied with the vapour production.
For the best experience we recommend using a 2.5Ω atomizer. If the resistance is lower than 2.5Ω please adjust the voltage around 3.5V.
Voltage adjust up
The factory default voltage is 4.0V, press the button 4 times then "VU" will be displayed on the LED.
Leave the button for 2 seconds after VU has been displayed on the LED. The LED will then display the voltage value.
Press the button to turn down the voltage, each press will raise in 0.1 V increments. When the voltage reaches the desired setting, stop pressing the button and wait for 3 seconds to save your setting. The IMotion2 V+ will then resume normal operation.
Voltage adjust down
Factory default voltage is 4.0V, press the button 5 times then "VD" will be displayed on the LED.
Leave the button for 2 seconds after VD is displayed. Then the LED will display the voltage value.
Press the button to turn down the voltage, each press will reduce 0.1 V . When the voltage reach your desired value, stop pressing the button and wait for 3 seconds to save your setting. And IMotion2 V+ will resume normal operation.
When IMotion2 V+ in "OF" mode the button will be locked. This function is for keeping the atomizer from turn on working in occasion when you are carrying the Imotion2V+ in your pocket or bag. And you still can change the settings under "OF" mode.
Factory default mode is: "ON". Press the button 6 times, the "SO" will be shown on LED. Then wait for few seconds the LED will display "On" or "OF" for your setting.
In this mode, you can see current battery voltage 3.0V-4.2V. Press 7 times to check it and LED will display "CB", and then battery voltage will be shown.
When the battery voltage lower than 3.3V, the LED will flash to warning and shows "LO", atomizer will stop vaping.
In "DR" mode, the IMotion2 V+ will display the resistance value of the atomizer, so that the user can check the atomizer type installed.
Press the button 8 times continuously, then DR will be shown on the display. Then the resistance of the current atomizer will be displayed.
Led light On/Off
Under LED ON mode, the LED will display the current voltage by every time you press the button during the atomizer operation. The "CB" function is also works under LED 'ON' mode.
Under LED OFF mode, the LED will not light up by pressing on the button during the atomizer operation. The "CB" function doesn't works under this mode.
Factory default mode is: ON. Press the button 9times, "LO" will be displayed on the LED, wait for few seconds, the LED will display current setting: "ON" or "OFF".
Dejligt at se der er kommet mods på banen :-) når det er sagt er dette et super mod der spiller max ..