VAMO V6 MOD - VV/WW (SS)
VAMO 6 is the of the Vamo Series. VAMO One of the absolutly best value mods VV/VW on the market.
It has a polished stainless steel body with unique ingravings . Besides from its many features it's really robust and stabile - and easy to use.
*** EOL ***
VAMO 6 BATTERI MOD - VARIABEL VOLT OG WATT
Superflot rustfri stål poleret mod, nyeste version af de oprindelig Vamo, spækket med funktioner, features og justeringsmuligheder. Kan benyttes med både 18350 og 18650 batterier.
3-6 Volt, 3-20 Watt
Mod virker med alle atomizers med 510 og ego gevind og benyttes variable watt indstillingen justerer mod'et selv output så det passer til de fleste atomizer modstande over 1.2ohm. Vamo har en cut-off ohm funktioner, der slår fra ved lavere ohms.
VAMO er et godt og prisbilligt mod med en imponerende liste af funktioner:
VAMO V6 - Contents of box:
1 pc. VAMO V6 MOD (Stainless Steel - Polished) with OLED display
1 pc. Top-ring (can be dismounted) for use with ie. T2/T3 (atomizers with skirts)
1 pc. Top 510-Adapter with USB outlet/port. Vamo can be used as powerbank (Ekstern battery)
1 pc. 18650 battery extension
1 pc. 18350 battery extension
1 pc. UK Usermanual
NB! No batteries, atomizer og charger are included - and should be purchased seperately.
Specifications for Vamo VV/VW MOD
- Variable Volt: 3~6.0V, (Trin af 0,5V)
- Variable Watt: 3~20W. (Trin af 0,1V
- Gevind: 510/EGO
- PWM (Pulse Width Modulation) output, op til 5A
- 5 Klik tænd/sluk
- Kan bruges med flere batterkonfigurationer: f.eks 1x 18650, 1x 18350 or 2x 18350
- Pol-beskyttelse og kortslutningsbeskyttelse
- Advarsel ved for lav ogm eller lav batteri
Denne varer er kun selv Vamo VV/VW Mod Body V2 uden batteri, atomizer, adapter eller lader.
Fuld samlet kan VAMO bruges sammen med 1 stk. 18650 eller 2 stk.18350 ved at fjerne nederst del af kroppen på mod'et kan man monterer 1 enketlt 18350.
VAMO MOD kræver ikke beskyttede batterier.
How to use chrome Vamo VV/VW Mod Body V6:
Turn On or Off:
Press the Power (large) button 5 times within 2 seconds.
Switch between VV and VW:
Press and hold + and - buttons for 3 seconds (v for volts, w for Watts).
Tap the + or - buttons to raise or lower output voltage (in .1 volt increments).
Tap the + or - buttons to raise or lower output wattage (in .5 watt increments).
With an atomiser or cartomiser installed on unit, press and hold the + button for 2 seconds. Atomiser resistance is displayed in ohms.
Battery voltage check:
Press and hold the - button for 2 secs to check actual battery voltage
The Vamo can display output voltage and wattage as an Average or as RMS (Root Mean Square). RMS is the actual and true output and is the one to use.
Press and hold the + button for 10 secs. If no2 is shown then the output is already set to RMS, no further action is required. If no1 is shown, release the button and press again for 10 secs until the display shows no2. This setting should not alter after a battery change, however if the vape feels warmer than expected please re-check setting.
LO-Ω : Atomiser resistance is too low (below 1.5 ohm).
LO-v : Atomiser shorted
Display will flash when battery needs replacing/recharging (approx 3.4v).
Voltage or wattage level resets when battery is removed, the mode does not.
Usage of eGo style cartomisers/clearomisers:
The Vamo has a recessed atomiser fitting with a large opening to accommodate the eGo skirt. Most popular atomisers and cartomisers will fit, however if you use a wide skirted unit (eg: Kanger T2 or T3 clearomizer) you will need to remove the beayty top ring.
Vamo Detachable VV & VW Mod V6.0 with RMS feature
The Vamo has a recessed atomiser fitting with a large opening to accommodate the eGo skirt. Most popular atomisers and cartomisers will fit, however if you use a wide skirted unit (eg: Kanger T2 or T3 clearomizer) you will need to fit a 510-EGO adaptor..
With the new detachable design, the Vamo Mod can work with 1pc 18650 battery or 2pcs 18350 batteries; also it can work with only 1pc 18350 battery.
Voltage is delivered via PWM (Pulse Width Modulation) with a maximum current of 5A.
In ‘long’ mode on the left the device can be used with one 18650 battery or TWO 18350 batteries. On the right in ‘short’ mode the device is using a single 18350 battery.
Protected type Li-Ion batteries will not work in this device – the over current protection renders them unusable as they usually have a current limit of 2.5 Amperes and this device uses current higher than that figure.. Please use High drain Safe rated batteries with no on-board protection for optimum use of this device.
Recommended batteries are IMR / AW type cells.
There are 3 buttons on the Vamo's body, please take a look at the image below: Metal buttoned versions are not marked with symbols
NOTE that the negative button is the LEFT button and the positive button is the RIGHT button.
Note: when a battery is inserted the screen may flash once and then turn off – the device is not yet turned on – you will need to click the power button 5 times to turn the device on. Your device is not faulty! Remember you must turn the device on!
Adjustment Button: Press the button to increase the voltage from 3.0v-6.0v in 0.1V steps, when you reach 6.0 v, it will start back from 3.0v. In wattage mode 3.0 to 20 Watts in 0.5 Watt increments when you reach 20 Watts it will start back from 3.0 Watts
Adjustment Button: Press the button to decrease the voltage from 6.0v-3.0v in 0.1V steps, when reach 6.0 v, it will start back from 6.0v. In wattage mode 20.0 to 3.0 Watts in 0.5 Watt increments when you reach 3.0 Watts it will start back from 20.0 Watts
Be aware of this feature as you might inadvertently set the voltage or wattage too high by accident.
Power Button: Press the power button 5 times, you can turn the device ON or OFF. Obviously the power button is used to activate the atomiser in actual operation. There is a safety cut out if the button is held down for more than 10 seconds duration.
Voltage to the atomising device can be provided in two ways from the mod.
RMS and AVG. It is recommended that users use the RMS (Root Mean Square) mode as this will be a more reliable and accurate method of delivering consistently accurate voltage.
• Hold either the OR button for 10 seconds to toggle between modes.
• RMS mode = N02 displayed on screen
• AVG mode = N01 displayed on screen
Whatever version of the mod you may have the voltage method should be remembered even when batteries are changed.
VARIABLE MODES -- VOLTS OR WATTS
Your device can operate in Variable Voltage mode or Variable Wattage mode.
• Constant voltage. In this mode, you can adjust from 3.0 to 6.0 Volts in 0.1 volt increments. The voltage that you set will be maintained as accurately as possible by automatic adjustment of current delivery.
• Constant power. In this mode, you can adjust from 3.0 to 20 Watts in 0.5 Watt increments. The wattage that you set will be maintained as accurately as possible via analysis of voltage and current delivery.
Change modes by holding AND buttons at the same time for 3 seconds.
Hold the button down for 3 seconds and the resistance of the attached atomiser will be displayed.
Battery power check
Hold the button for 3 seconds to display current battery voltage.
Additional Safety features and Functions:
- Fremstillet i rustfrit stål.
- 510 & EGO kompatibel.
- 5 klik for on/off.
- Variabel watt fra 3W - 20W (0,5W intervaller).
- Variabel volt fra 3V - 6V (0,1V intervaller)
- Bruger 1 x 18350 eller 1 x 18650 batterier.
- Kan bruges som power bank (output adapter inkluderet).
- Lys OLED display.
- Beskyttet mod kortslutning.
- Fejlstrømbeskyttelse (forkert monteret batteri)
- Flotte indgraveringer lavet med laser.
- Kan vise modstanden på den påsatte atomizer, og resterende strøm på batteriet.
- Størrelse: Diameter: 22 mm og ca. 140 mm (med 18650 adapter monteret)
There is no reviews yet. Be the first to write us your opinion